Toll Free Phone Quick Reference Guide. Knowing Your Sewing Machine. Name of Machine Parts and Their Functions. Pattern Selection Dial Choose from 10 different stitches.

Author:Juzuru Tojajinn
Language:English (Spanish)
Published (Last):27 May 2007
PDF File Size:15.49 Mb
ePub File Size:18.28 Mb
Price:Free* [*Free Regsitration Required]

Quick Links. See also: Operating Manual. Instruction Manual. Table of Contents. Single needle unison feed lock stitcher with large hook pages. Single needle unison feed lock stitcher with vertical large 26 pages. Single needle unison feed lock stitcher with horizontal 26 pages. Always unplug this sewing machine from the electrical outlet immediately after using and before cleaning. If your sewing machine is fitted with a 3 pin non-rewireable BS plug then please read the following. Parts code for zigzag presser foot: Insert the foot controller plug, located between the foot controller and the power supply plug on the cord, into the jack on the machine.

Insert the power supply plug into an electrical outlet. See fig. Remove the power supply plug from the electrical outlet. Raise the needle bar to its highest position.

Lower the presser foot. If a needle is already installed, remove the needle by loosening the needle clamp with a coin and pulling the needle down. Raise the needle to its highest position by turning the balance wheel toward you counterclockwise , and raise the presser foot lever.

To change your machine to the free-arm style, lift up on the extension table and pull it out. Stitch widths and lengths are shown on the following page. Page Reverse Sewing Lever Reverse Sewing Lever To sew in reverse, press down the reverse sewing lever as far as possible and hold it in that position while lightly stepping on the foot controller. To sew forward, release the reverse sewing lever.

Reverse sewing is used for locking and reinforcing seams. Raise the needle to its highest position by turning the balance wheel toward you counterclockwise and raise the presser foot lifter. Open the shuttle cover behind the extension table on the front of the machine and remove the bobbin case by pulling its latch toward you and pulling it out from the shuttle race fig.

Raise the presser foot using the presser foot lifter and turn the balance wheel toward you counterclockwise to raise the thread take-up lever to its highest position. Pull up the spool pin and place a spool of thread on this pin. Raise the presser foot and the needle to their highest positions.

With your left hand, hold the end of the upper thread. With your right hand, turn the balance wheel toward you counterclockwise until the needle moves down and back up again to its highest position. Page Twin-Needle Sewing Twin-Needle Sewing Your sewing machine is designed for twin-needle sewing which allows you to sew using two upper threads.

You can use the same color or two different colors of thread for decorative stitches. Twin-needle sewing works well with these stitches: the Straight Stitch -and the Zigzag Stitch 2. Puede usar el mismo color de hilo o dos hilos de colores distintos para puntadas decorativas. It may need to be adjusted when you change fabric or thread type. NOTE: It is recommended that a test sample be made on a fabric scrap before sewing on your project.

For most sewing applications, no adjustment is needed. When sewing with thin thread on thin fabrics, the thread tension may not be adjusted adequately with the upper tension control dial. Page Straight Stitching Straight Stitching Pattern Center needle position Left needle position The Straight Stitch or 11 is used for top stitching and sewing lightweight fabrics.

Starting Sewing fig. Set the pattern selection dial to the appropriate Straight Stitch or 11 with the desired length. Page 33 Para empezar a coser fig. It is recommended to sew using the Straight Stitch at the beginning and end of the Zigzag Stitches. Set the pattern selection dial to Both the threads should be the same color as the fabric. Each is explained below. Place the reinforcement fabric under the tear to be mended. Use a tighter thread tension than normal.

It is recommended to practice making a buttonhole on a scrap piece of fabric before attempting it on the actual garment. When making buttonholes on soft fabrics, place stabilizer material on the underside of the fabric. Buttonhole-making is a simple process that provides reliable results. To secure the stitching, turn the material 90 degrees counterclockwise, set the pattern selection dial to the Straight Stitch with the desired length and sew to the edge of the front bar tack.

Page Buttonhole Fine Adjustment Buttonhole Fine Adjustment If the stitching on the two sides of the buttonhole do not appear uniform, the following adjustments can be made. After sewing the left side of the buttonhole, stitch the right side and observe the feeding. Measure the distance between the buttonholes and set the pattern selection dial to the Zigzag Stitch 2, 3 or 4 with the desired width.

Distance between holes 1. Page Zipper Insertion Zipper Insertion Pattern Straight Stitch The zipper foot is used to sew on various types of zippers and can easily be positioned to the right or left side of the needle. When sewing the right side of the zipper, attach the shank to the left pin of the zipper foot.

Set the pattern selection dial to the Straight Stitch with the desired length. Loosen the tension of the upper thread to about 2 so that the lower thread lies on the underside of the fabric. Place the darning plate on the needle plate as shown in fig. Place the portion to be darned under the presser foot together with a fabric underlay for reinforcement.

Page Appliques Appliques Pattern 2, 3, 4, 5 Zigzag Stitch An applique is created by cutting a contrasting piece of fabric into a shape to be used as a decoration on a garment or project. Baste the cut design to the fabric in the desired location where desired. Place the darning plate on the needle plate. Set the pattern selection dial to the appropriate Zigzag Stitch 2, 3, 4 or 5.

Sew moving the hoop slowly along the lettering at a constant speed. To secure the stitching, set the pattern selection dial to the Straight Stitch with the desired length and sew a few stitches at the end of the last letter. Loosen the face plate screw as shown in fig. Remove the face plate from the machine as illustrated in fig.

Replace the sewing light bulb. Page Oiling Oiling 1. Remove the power supply plug from the outlet. Put 2 to 3 drops of oil at each of the points indicated in fig. After oiling, run the machine at a fast speed without thread installed for a short time. Cleaning the Shuttle Race 1. Remove any accumulated lint and thread with a brush from the retaining ring, hook, driver and race body. A cloth dampened with machine oil should be used to wipe the shuttle race clean of lint.

Remove the presser foot holder and the needle. Remove the needle plate using a coin or screwdriver to take out the screws. Clean the lint from the upper part of the feed dogs and shuttle race body with a brush. Page 17 Page 16 Bobbin is not threaded Upper thread is properly in the tangled. Page 14 Page 16 Upper thread Lower thread tension is too tension is too Page 22 Damaged or worn needle is used. Page 6 Thread is tangled. Pages Darning plate is installed. It may become necessary to reship the sewing machine.

Improper packing or improper packing material could result in damage during shipping. Instructions for repacking the machine are illustrated below. Page Index Accessories Page Index Accessoires Page Indice Accesorios This manual is also suitable for: Vx - free arm sewing machine Ls Ls Print page 1 Print document 67 pages. Cancel Delete.

Sign In OR. Don't have an account? Sign up! Restore password.


Brother LS-2125i Instruction Manual



Brother LS-2125I Sewing Machine Instruction Manual



Brother LS-2125i User Manual


Related Articles